For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-9C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits PRS-6, PRS-7, and PRS-8 stands made before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
The PRS-4.2 is a professional quality bench mount repair stand designed and built to withstand the rigors of everyday shop use. Includes three mounting holes, making it possible to clamp as high as 16.25" (41cm) from the bench surface. - The 100-3D Micro-Adjust clamp grips nearly any tube from 7/8" to 3" (23mm to 76mm), including aero tubes - The clamp jaws are nominally 2.75 inches (7cm) wide - Clamping height can be raised from 6.5" to 16.25" (16cm to 41cm) above the bench surface - Clamp rotates 360 degrees - Heavy gauge steel tubing - Chrome plated for durability
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).
Built to withstand the rigors of every day shop use, the PRS-3.3 is the stand of choice for professional mechanics around the world. Stand height and clamp position are firmly secured in place using our proven lock block system. Built from heavy-gauge oversized steel tubing, then chrome plated and powder coated for years of carefree use. The PRS-3.3-2 features our 100-3D Micro-Adjust Clamp with narrow clamping jaws and a dual-stage, cam-actuated system that quickly adjusts to accommodate nearly any seat tube or frame size. - Maximum weight capacity: 120 lbs. (54 kg) - Clamp capacity: 0.875" to 3" (22–76 mm) diameter tubes, including aero tubes - Clamp jaws are nominally 2.75" (70 mm) wide - Clamp height: adjustable from 50" to 62" (128–158 cm) - Includes #105 Cast Aluminum Work Tray & RPP-1 Repair Stand Post Protector - Can be installed onto the #130 Repair Stand Base or bolted directly to the floor using the FP-2 Floor Plate (both sold separately)
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
$9.14 - $25.08
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
Page 1 of 1